DFC
What Does a Spiral Duct Machine Do? Working Principle and Applications
  • 19 Nov 2026

What Does a Spiral Duct Machine Do? Working Principle and Applications

 

What does a spiral duct machine do?

The machine forms the coiled sheet metal strip, locks the seam and cuts the duct to the required length; the result is straight, round ventilation duct. Elbows and fittings are made on separate machines. The same machine is also known as a round duct machine or spiral tubeformer.

The DFC Spiral Duct Machine works with a 137 mm wide strip. Seaming and cutting are hydraulic: the seam is stronger than with conventional methods, the cut edge is burr-free and no extra grinding is needed before assembly. The machine is offered in two designs: strip type and mold type.

1. Diameter range: your smallest and largest duct

First check that the machine’s diameter range covers your projects. Small diameters are used in branch lines inside buildings, large diameters in main lines and industrial plants; the machine must cover both ends of your work.

The DFC Spiral Duct Machine works from Ø100 to 1250 mm (strip type) and Ø100 to 1600 mm (mold type); 1600 – 2000 mm is optional. Model codes: DFC YKM 0001 for Ø1250, DFC YKM 0002 for Ø1600, DFC YKM 0003 for Ø2000 and DFC YKM 0004 for the mold type. Standard diameter sizes from Ø100 to Ø2000 are listed on the product page.

2. Sheet thickness and material

Galvanized steel and stainless steel have different thickness limits, so a quotation should state both. The lower thickness limit also rises with diameter: large duct cannot be made from very thin sheet. Always ask for thickness together with diameter.

The DFC Spiral Duct Machine processes 0.5 – 1.2 mm galvanized and 0.4 – 0.9 mm stainless steel sheet. According to the product page table, Ø100 uses 0.5 – 1 mm and Ø1600 uses 0.8 – 1.2 mm (see the speed table below).

3. Production speed depends on diameter

Duct speed is not a single number: at small diameters the machine produces more metres per minute, at large diameters speed drops. When comparing quotations, put the speeds for the same diameter and thickness side by side.

DIAMETER SHEET THICKNESS (mm) DUCT PRODUCTION SPEED
Ø100 0.5 – 1 14 m/min
Ø500 0.6 – 1.2 2.8 m/min
Ø1000 0.7 – 1.2 1.4 m/min
Ø1600 0.8 – 1.2 1.2 m/min

Ask for the speed at the diameters you produce most, and calculate your daily duct output from it.

4. Power, electrical supply and compressed air

The machine’s power sets the requirements for your workshop’s electrical supply. Because mains frequency (50 or 60 Hz) differs between countries, it must be stated in the quotation. Some spiral duct machines also need compressed air, which adds a compressor and an air line to the investment.

The DFC Spiral Duct Machine draws 10.5 kW (strip type) or 15 kW (mold type) and runs on 380 V / 3-phase, 50/60 Hz. It needs 6 – 8 bar compressed air, so a compressor and air line must be ready in the workshop. The product page gives the hydraulic oil capacity as 10 lt – 6 lt.

5. Automation: what reduces the operator’s work?

Two machines with the same diameter range often differ in automation. Ask the supplier to state which features are standard and which are options.

The DFC Spiral Duct Machine has automatic sheet loading, automatic angle adjustment, automatic duct lubrication and automatic seam crimping. Strip feeding can be chosen as “automatic strip” or “standard strip”; each option has its own stock code on the product page.

6. Duct length and stand

The machine cuts the duct to length; the finished duct is carried and unloaded on a stand. If you produce long duct, check the stand length and the automatic tilting option.

The DFC Spiral Duct Machine produces duct from 250 to 6000 mm long. A 3 m stand is supplied as standard, and an automatic tilting stand is available.

7. Floor space and weight

Plan the floor space with the stand length and the coil area added to the machine dimensions. Weight matters for the floor and for loading and unloading.

The DFC Spiral Duct Machine measures 1600 × 3500 × 3050 mm and weighs 1950 – 2600 kg depending on the model.

Buyer’s checklist

All DFC values in the table come from the DFC Spiral Duct Machine product page. Fill in the same rows for every quotation you compare.

CRITERION WHAT TO CHECK DFC STRIP TYPE DFC MOLD TYPE
Diameter range Are your smallest and largest ducts within range? Ø100 – 1250 mm Ø100 – 1600 mm
Optional large diameter Will you make duct above Ø1600? 1600 – 2000 mm optional 1600 – 2000 mm optional
Galvanized sheet Is your thickest sheet below the upper limit? 0.5 – 1.2 mm 0.5 – 1.2 mm
Stainless steel sheet If you work in stainless, is a separate value given? 0.4 – 0.9 mm 0.4 – 0.9 mm
Strip width Does your strip supply match this width? 137 mm 137 mm
Production speed Is the speed for your diameters stated? 14 m/min at Ø100, 1.2 m/min at Ø1600 14 m/min at Ø100, 1.2 m/min at Ø1600
Power Is your electrical supply sufficient? 10.5 kW 15 kW
Electrical Do voltage and frequency match your mains? 380 V / 3-phase, 50/60 Hz 380 V / 3-phase, 50/60 Hz
Compressed air Are a compressor and air line ready? 6 – 8 bar 6 – 8 bar
Duct length Is your longest duct within range? 250 – 6000 mm 250 – 6000 mm
Stand Stand length and tilting option? 3 m; automatic tilting stand available 3 m; automatic tilting stand available
Machine dimensions Is there space in the workshop? 1600 × 3500 × 3050 mm 1600 × 3500 × 3050 mm

Warranty and service: get it in writing

The machine will run for years; who comes, how fast and at whose cost when it fails matters as much as the price. Ask every supplier to answer these questions in writing.

TOPIC QUESTION TO ASK DFC SPIRAL DUCT MACHINE
Warranty period How many years of mechanical and electronic warranty? 2-year mechanical + 2-year electronic
Service response How many days until a technician arrives? Does it apply abroad? 1 – 3 business days in Türkiye and abroad
Spare parts For how many years are spare parts supplied? 10-year spare parts supply guarantee
Remote support Can PLC and automation faults be checked remotely? Internet-based remote access with PLC and automation support
Installation and training Are installation, commissioning and operator training included? Included in the delivery
On-site service under warranty Does the warranty cover service as well as parts? Service is covered for machine-related failures; when required, travel and accommodation are covered by DFC Makine

What completes a spiral duct line?

A spiral duct machine makes straight duct. Elbows, reducers and fittings need other machines in the line. We explain which machine is used at which stage in Machines Needed to Set Up a Ductwork Workshop, and how to choose an elbow machine in the Round Elbow Machine Buying Guide.

Decide with seven questions

  1. Are my smallest and largest duct diameters within the machine’s range?
  2. Is my thickest galvanized and stainless sheet below the limit, and do I know the lower thickness limit at large diameters?
  3. Does the quotation state metres of duct per minute for the diameters I produce most?
  4. Are 380 V / 3-phase power and 6 – 8 bar compressed air ready in the workshop?
  5. Are sheet loading, angle adjustment, lubrication and seam crimping automatic, and which are options?
  6. Do the duct length and the stand (tilting) cover my needs?
  7. Are warranty, service response time, spare parts, installation and training stated in writing?

Frequently Asked Questions

Is a spiral duct machine the same as a round duct machine?

Yes. Both names, as well as spiral tubeformer, are used for the machine that winds sheet metal strip and locks its seam to produce round ventilation duct. Spiral Duct Machine is the name DFC uses in English (Turkish: Yuvarlak Kanal Makinesi).

What diameters and sheet thicknesses does the DFC Spiral Duct Machine handle?

Ø100 – 1250 mm with the strip type and Ø100 – 1600 mm with the mold type; 1600 – 2000 mm is optional. It processes 0.5 – 1.2 mm galvanized and 0.4 – 0.9 mm stainless steel sheet.

Does a spiral duct machine need compressed air?

The DFC Spiral Duct Machine works with 6 – 8 bar compressed air, so a compressor and air line are needed. The electrical connection is 380 V / 3-phase, 50/60 Hz.

How many metres of duct per minute does a spiral duct machine produce?

Speed depends on diameter. On the DFC Spiral Duct Machine it is 14 m/min at Ø100, 2.8 m/min at Ø500, 1.4 m/min at Ø1000 and 1.2 m/min at Ø1600.

What are the warranty and service terms?

2-year mechanical and 2-year electronic warranty, technical service within 1 – 3 business days in Türkiye and abroad, and a 10-year spare parts supply guarantee. Installation, commissioning and operator training are included in the delivery.

Which countries has the DFC Spiral Duct Machine been exported to?

According to the product page, it has been exported to a total of 41 countries, including Albania, the United Arab Emirates, France, Algeria and Russia.

Send us the diameter range, sheet thickness and daily duct output you need, and we will prepare the DFC Spiral Duct Machine quotation and technical file accordingly.

Related Product Pages

DFC Machinery & Engineering